If I have a Microwizard Timer, the power adapter, the USB adapter and cable, but do not have access to the start section for the starter / trigger switch, is there still a way to test connectivity and working communications between the Timer and the GPRM v10 software?
Nicholas
Testing Connectivity without full hardware setup
- pack529holycross
- Master Pine Head
- Posts: 555
- Joined: Wed Dec 26, 2007 4:25 pm
- Location: Dr. Phillips, Florida
- Contact:
- gpraceman
- Site Admin
- Posts: 4926
- Joined: Fri Jun 20, 2003 12:46 am
- Location: Highlands Ranch, CO
- Contact:
Re: Testing Connectivity without full hardware setup
To a limited extent. You can open up the Hardware Options screen and at least verify that you have communications.
1) Click on the Start Testing button.
2) Disconnect the power from the timer
3) Wait a couple of seconds
4) Reconnect the power to the timer
In the Timer Data box you should see a Micro Wizard copyright statement show up. If so, you have communications. If not, start going through the troubleshooting information in the software's help file.
You really need to have the start switch handy in order to do a full timing test.
1) Click on the Start Testing button.
2) Disconnect the power from the timer
3) Wait a couple of seconds
4) Reconnect the power to the timer
In the Timer Data box you should see a Micro Wizard copyright statement show up. If so, you have communications. If not, start going through the troubleshooting information in the software's help file.
You really need to have the start switch handy in order to do a full timing test.
Randy Lisano
Romans 5:8
Awana Grand Prix and Pinewood Derby racing - Where a child, an adult and a small block of wood combine for a lot of fun and memories.
Romans 5:8
Awana Grand Prix and Pinewood Derby racing - Where a child, an adult and a small block of wood combine for a lot of fun and memories.
- FatSebastian
- Pine Head Legend
- Posts: 2818
- Joined: Wed Jun 17, 2009 2:49 pm
- Location: Boogerton, PA
Re: Testing Connectivity without full hardware setup
FWIW, I once did a complete simulated race with a Microwizard timer sitting on the workbench without a starting switch. Once GPRM has received a test signal as gpraceman describes, simply continue to unplug and reconnect the power to the Microwizard timer each time you want to simulate having tripped the starting gate switch.pack529holycross wrote:You really need to have the start switch handy in order to do a full timing test.
- gpraceman
- Site Admin
- Posts: 4926
- Joined: Fri Jun 20, 2003 12:46 am
- Location: Highlands Ranch, CO
- Contact:
Re: Testing Connectivity without full hardware setup
True, but that is not very convenient, IMO.FatSebastian wrote: Once GPRM has received a test signal as gpraceman describes, simply continue to unplug and reconnect the power to the Microwizard timer each time you want to simulate having tripped the starting gate switch.
Randy Lisano
Romans 5:8
Awana Grand Prix and Pinewood Derby racing - Where a child, an adult and a small block of wood combine for a lot of fun and memories.
Romans 5:8
Awana Grand Prix and Pinewood Derby racing - Where a child, an adult and a small block of wood combine for a lot of fun and memories.
- gpraceman
- Site Admin
- Posts: 4926
- Joined: Fri Jun 20, 2003 12:46 am
- Location: Highlands Ranch, CO
- Contact:
Re: Testing Connectivity without full hardware setup
All you really need is a switch and a telephone cord. You can get the switch from Radio Shack and you probably have a telephone cord laying around the house. Wire yourself up test switch.
Randy Lisano
Romans 5:8
Awana Grand Prix and Pinewood Derby racing - Where a child, an adult and a small block of wood combine for a lot of fun and memories.
Romans 5:8
Awana Grand Prix and Pinewood Derby racing - Where a child, an adult and a small block of wood combine for a lot of fun and memories.